Remember those pizza boxes on the back porch? Here’s the result. This was the morning after a 1AM installation session, where we had to move all the furniture into the dining room and jockey the white couch (the 4-ton sleeper) around the tiles as we laid them down. The result is a warm, comfy floor that brings a new color into the neutral space, and lightens up the whole room

Now, to get rid of that hideous brass fireplace surround.

We moved furniture back into the living room on Saturday night after everything got final coats of paint. The area above the mantel is supposed to be darker than the wall, but it’s not dark enough for us yet. It’s great to have everything coming back to normal again, and even better to look at the base of the walls and see crisp white paint on clean new baseboard going around the length of the room. For your amusement (and my indulgence), here are some before and after shots. I don’t have any good shots of the room in original condition, unfortunately.

6.4.05 This is the day I tore the nasty wood paneling off the wall. (note the shitty floor, pre-sanded.)

6.4.05 After the paneling came down, before I patched the wall (note the chimney.)

This afternoon.

This is the basic crown molding sold at Lowe’s and Home Depot, clamped into place for test-fitting and basic aesthetic testing. At first I had it lined up with the top of the box, so it began about 4″ down the box and (to my mind) was squishing the top box too much proportionally. My initial plan was to tack it into place here, then see if I could have a 3/4″ plank planed down to 1/2″ at a lumberyard somewhere and basically just tack it on top of the molding. This would have left me with a thick lip at the top of the mantle though—the squared top of the molding is about 1/4″, plus a 1/2″ board == eccch.

My second thought was to mill the sides of a plank down to fit the bevel of the molding (tip: all crown molding is essentially a thin board turned on its side so that it doesn’t create a 45° wedge at the back, which makes it undesirable for finishing the top of, say, a mantle) and fit it to the mantle, then tack the molding onto it and into the side of the box. This would be considerably more difficult but the end product would be much more pleasing.

Another thing to note is that with this particular crown molding, the angle at the back is not a perfect 45°; it’s somewhere around 32°, which makes fitting the bevel that much trickier. I cut the molding according to the measurements and test-fit it, then measured both the box and the outline of the molding to find the final edge size. (Sure, your fancy “New math” might have helped here, but remember, this house is out of square in five dimensions.)

Cutting the long edge of the plank was easy on the table saw, but cutting the short edges was tricky because my compound miter saw only has a reach of about 7″, and this board is 8 1/4″ wide. So I had to revert to the circular saw, adjusting the blade by guesswork and praying for good results.

And luckily, it seemed to work. I got true 32° cuts from the circular saw in a straight line, and fit the plank into place. Next, I had to jigsaw out the odd scalloped shape of the bumpout above the fireplace into the back of the plank—both edges come out about 1/8″ further than the center— and plane out any inconsistency left so that it fit as flush as possible.

The end result has a few very minor hiccups here and there, but overall looks very good, and turned out better than I’d dreamed it might. I have to cut and fit shims on the top to support the plank, and then the whole thing gets permanently fastened to the frame.

The next step is to cut down those small planks on the right side and fit them around the sides so that they meet the kickplates on the wall, covering up the lousy edging job the floor guy did around the fireplace and the lousy brickwork we inherited. Then, putty and caulk go in to fill any rough edges, a final sanding, and finish paint goes on.

Here’s the fireplace with added wings on the edges, sanded and primed. If I can clear the decks this weekend I’m hoping to finish this project off and move back in before next Monday. Cross your fingers.

This took a little longer than I thought because I built the boxes with 45° angles to avoid having the edge of the woodgrain to deal with when I finish. Clamps are a wonderful invention, and I need to buy more of them.

This is the other side. Under this section we’ll put the rounded bead, and above it will go a milled edge finished off with a 1/2″ flat cap.

(Here’s more information and pictures.) Sorry about the yellow cast to the picture; I forgot to change the white balance setting.

In general, this year has been different than the last, because we’ve ignored our house for eight months while our businesses have been getting traction. Sure, I was able to get the living room windows scraped, cleaned, and painted, and Jen made good headway on the garden, but that was in the spring, centuries ago, when it was warm.

Last week, after a few checks came in, we decided to call in some pros and finally get our living room wired. Up until now, it’s been incomplete, with a coat of paint on the walls, no baseboards, and a cardboard facade over the nasty fireplace brick.

Our electrician recommended recessed lighting for the ceiling as a way to warm up the space evenly and add some variation to the lighting zones. The living room at one time had a central chandelier which was taken down and capped over, so there was no light switch in the whole room.

During:

The blue tape in this shot is the outline of what will soon be the pass-through French door into the doctor’s office. To the left of the door on the other side is a half-bath.

The hole in the center is the location of the old chandelier box, which is now gone. The little holes behind that are from the wire hopping the joists. They will be covered by drywall at the end of the job.

The housings are HALO brand 6″ fittings; I think in hindsight I’d choose the 4″, and that’s what I’m going to specify for the kitchen. Overall, the light they throw is warm and full. We put the two over the fireplace on their own dimmer, and the other eight are ganged on a 600w dimmer of their own.

This is step one; The next phase is to wire the baseboards and get the room on its own circuit. We’ll be putting two plugs in on each baseboard as well as cable, phone and ethernet jacks. Phase three is to have professional drywallers come in and put 1/2″ sheetrock up on the ceiling over the plaster and around the lights so that the ripples and patches in the ceiling are covered for a smooth appearance.

All of the baseboards have been pulled out (with the exception of the one behind the radiator) and walls have been patched. At some point I’ll get the time to run wiring and fabricate new baseboards (and we’ll get the money to have them hooked up), and we can close up the walls. In the meantime, I started building a frame around our shitty looking fireplace and tacking up cardboard to block out how large the cover will be.

I’m going to follow the pseudo-Federalist/Colonial woodworking in the rest of the house and keep the cover as simple as possible. When it’s done, the exposed brick will get painted with hi-temp flat black and the wood will get painted with the gloss white we have on the rest of the woodwork.

This is the living room wall after two coats of mud, a coat of Kilz, and a coat of white paint. Go to Flickr for the full set-I’ll be posting all of these on the houseblog when we get back from Annapolis this afternoon.

Here’s the living room with all the edges cut in, which makes a drastic difference. He got everything except the corners and under the radiators, which he’ll do by hand. Today he’s going to finish the hand work and then start on the stair treads before staining.